Pool Service in Studio City, CA

Studio City is where we work from. Our office is at 4121 Radford Ave, Ste. #214, Studio City, CA 91604 — so this is the shortest drive on the whole map, and the only community where the truck is already nearby rather than on its way over a hill.

That matters in one practical way: a second look at an equipment pad costs us less here than anywhere else we serve, so ask for one rather than guessing at a symptom over the phone.

What is different about pools in 91604

Studio City pools are mostly older than the equipment attached to them, and that mismatch is the theme of the whole neighbourhood.

Older shells, newer pads

A great many pools here were built with the houses in the 1950s and 60s: modest in size, plastered more than once since, and often on their third generation of equipment. The shell remembers every resurface; the pad has been modernised a piece at a time, usually in an emergency, by whoever was available that week.

Hill and flat in one ZIP code

South of Ventura the lots run up toward Laurel Canyon — small, steep, tight side-yard access and gates that a service has to negotiate every visit. North toward the river the streets are flat and shaded by mature trees that were planted when the houses were new and now hang over the water.

What most often goes wrong here

Four patterns, and none of them is really about the water.

A pool that has been replastered too many times to acid wash
An acid wash removes a thin layer of the finish, and it only works while there is a finish left to spend — roughly half an inch. On a sixty-year-old Studio City pool that has already been washed once or twice, the honest answer is sometimes that it needs resurfacing rather than another wash. That is a cheaper conversation to have before the drain than after.
A modern pump bolted to 1960s plumbing
A variable-speed pump saves money by running slowly for longer, but on old undersized pipe and a small filter, slow means the pool never turns over and the heater will not see enough flow to fire. The pump is not faulty. It was programmed for a pool it is not attached to.
Automation that half works
Controllers get retrofitted onto valve setups they were never designed around, then inherited by a new owner with no manual. The spa fills the pool, a valve stays where it was left, and the app has not connected since the router was changed. Automation repair starts by finding out what is actually plumbed where.
One skimmer against a mature tree canopy
Older pools were built with a single skimmer for a garden that had not grown in yet. Fifty years on, the same skimmer is working against a full canopy, its basket fills mid-week and the pump spends days pulling against a restriction it should never see.

Our services, from the office up the road

Weekly pool maintenance

The full panel, net and vacuum, tile and walls brushed, every basket emptied and the whole pad inspected. One or two visits a week, year round.

Green to Clean

For a pool left alone during a shoot, a remodel or a sale. The water comes back without draining, swimmable in about two days, with the filter cleaned two or three times along the way.

Acid wash

Also called a drain and clean. We measure what plaster is left before recommending it, which on pools of this age is the whole decision.

Equipment repair

Pumps, filters, heaters, salt systems, plumbing, electrical components, lights and time clocks — the mixed-vintage pads this neighbourhood is full of.

New plaster start-up

Four weeks of close attention after a resurface: daily nylon brushing, calcium hardness 200–400 ppm, pH 7.2–7.6, no salt for the first 28 days.

The Studio City route

We run routes rather than a radius, and this one begins at the office.

A fixed day, every week

Your pool sits on one day of the week and stays there. Ask which days have room in Studio City when you call.
Short journeys change what is practical

Coming back to check a repair, or fitting in a party cleaning with 24 hours' notice, is a small thing from a mile away and a large one from across the Valley.
The same written checklist every visit

So you can tell what the water read and what was touched without standing at the gate to watch.

Request a free quote What it costs in Los Angeles

Questions Studio City owners ask

Where are you actually based?

4121 Radford Ave, Ste. #214, Studio City, CA 91604. We are a family-owned company and this is the office, not a mailbox in a neighbourhood we visit twice a month. Studio City pools are the closest work we do.

Can my pool be acid washed if it has already been replastered twice?

Only if there is enough plaster left — about half an inch is the working minimum, because the acid takes a layer of finish with the stain. We check before recommending it. If the surface is too thin, an acid wash buys you a season and costs you the shell, and we will say so.

How much does it cost to have someone come out and fill your pool?

Water haulers charge by the load and it is not cheap, but the question usually arrives for the wrong reason. Most pools that need filling are either evaporating normally in summer or losing water somewhere, and a truck fills both equally. It is also why we never drain a green pool to fix it — Green to Clean restores the water in place, and an empty pool in Los Angeles carries risks of its own.

The previous owner set up the automation and left no instructions. Can you take it over?

Yes, and it is a common first job here. We trace which valve does what, set pump speeds and time clocks to the seasons rather than to whatever they were left on, and hand you a system you can operate. We install Pentair and Jandy equipment, so those controllers are familiar ground. What we repair.

Around Studio City

Tell us the street, roughly how big the pool is, what is on the equipment pad and what is bothering you. Being local, we would rather look at it than guess. Request a free quote.